Methven Kiri Manual do Utilizador descarregar pdf (Página 4)

4 5

It is Important to note at this stage, very hot water MAY flow through either outlet depending on

where the diverter is set too and can cause serious burns if care is not taken !!!.

3. Take note of the outlet temperature of the shower using a suitable testing equipment.

4. If the maximum temperature requires adjusting . Remove the Temperature control knob (3) and adjust

the Thermostatic mixing valve spindle.

To increase the outlet temperature , Slowly turn the spindle of the anti-clockwise

To decrease the outlet temperature , Slowly turn the spindle of the clockwise

5. When the desired temperature is achieved. Refit and secure the Thermostatic mixing valve control

knob (3) lining up the pin in the Knob with the Temperature stop ring(12).

6. Turn off the Shower valve.

Parts Reference Drawing

Installing the Product

When installing the assembly into the wall cavity , for ease of installation and maintenance you should aim to

keep the access hole as large as possible whilst ensuring there will still be enough room to be able to create

a suitable contact between the wall and concealing plate using a suitable silicon sealant to create a water tight

joint between the wall and concealing plate.

This product has been designed to fit in a cavity with a minimum depth of 60mm. For deeper cavities you may

need to create a suitable mounting bracket in the cavity to securely mount the valve assembly. We recommend

a mounting depth of between 60/67mm from the front face of the tiles. Failure to take this into account will mean

that the concealing plate will not be able to be fixed onto the valve assembly. Refer to Page 7 ‘Line drawing’.

1. Ensure that both the Hot and Cold mains water supplies are isolated.

2. Fix the shower valve assembly into the wall cavity ensuring the diverter assembly is at the top and the bath

fill on / off control is at the bottom. If done correctly the ‘Hot’ inlet port to the thermostatic mixing valve will be

in the centre of the valve assembly to the left hand side.

3. Connect the respective Hot and Cold water supplies to the Hot and Cold inlet ports of the thermostatic

mixing valve making sure that all seals, filters olives are fitted and joints sufficiently tightened.

4. Connect the left hand diverter outlet to one of your outlets and the right hand diverter outlet to the

other outlet connection and the bath fill outlet to the bath fill.

Important : Before fitting the concealing plate it is essential that all joints are checked for leaks. Failure to do

so could result in flooding or water damage within the cavity over a long period of time that may

not be immediately evident. Therefore :-

5. Secure the Diverter knob (2) to the Diverter assembly (31) and Bath fill on/off knob (2) to the stopcock

assembly.

6. Secure the temperature control knob to the thermostatic mixing valve (32). To secure the temperature

knob in the correct position . Please refer to ‘Maximum temperature setting and adjustment’.

7. Ensuring all joints have been secured and tightened , Turn on both Hot and Cold water supplies.

8. Turn the diverter knob towards the side connected to bath fill outlet.

9. Taking care , turn on the thermostatic mixing valve. If no water appears from the outlet of the bath fill ,

rotate the bath fill on/off knob. Water should now be flowing through the bath fill outlet, check all joints

for signs of leaks . Turn off the bath fill on/off knob. Turn the diverter knob towards one of the other

connected outlets. Water will now flow through this outlet. Repeat this process for the remaining outlet.

Any leaking joints should be immediately rectified. It may be a good idea to leave the shower running for

several minutes to ensure the joints are water tight and no leaks appear.

10. When you are confident that all joints are watertight. Turn off the thermostatic mixing valve.

11. Noting each of the three control knob positions , remove the bath fill , thermostatic mixing valve and

diverter control knobs (The positions will be required after fitting the concealing plate to refit the control

knobs in the correct operating positions).

12. Ensuring correct orientation, Fit the concealing plate (28) to the valve assembly. When fitting the

concealing plate , a suitable sealant should be used to create a waterproof joint between the concealing

plate and wall.

13. Refit and secure the Diverter control knob to the position it was removed in point 11.above.

14. To refit the thermostatic mixing valve temperature knob , Please refer to ‘Maximum temperature

setting and adjustment’.

15. Refit and secure the bath fill control knob to the position it was removed in point 11.above.

Maximum Temperature Setting and Adjustment

Whilst the Temperature of your Thermostatic mixing valve has been factory tested and calibrated, you will

need to perform a slight initial adjustment to suit your system operating setup. To do so :-

1. Loosely fit the Thermostatic mixing valve control knob (3) to the Thermostatic mixing valve. Note, whilst

fitting the Knob, there is a Temperature stop pin (17) inside the knob which is required to line up with the

Temperature stop ring (12).

2. Taking extreme care, Slowly turn on the Thermostatic mixing valve and gently rotate the control knob

to the maximum temperature position. Let the shower run for several minutes to ensure the correct

blend of Hot and Cold water and the maximum outlet hot water temperature has been achieved.

Part Code Description Part Code Description

1 00105055 Valve Body 24 00512119 Connector

2 00142875 Diverter Handle 25 00514592 Connector

3 00142872 Temperature Handle 26 00515537 Shroud

4 00400014 O' Ring 27 00515826 Adaptor

5 00400015 O' Ring 28 00550740 Plate

6 00400246 Filter Washer 29 00601113 Pair of Fixing Screws and Plugs

7 00400380 O' Ring 30 00603719 Check Valve

8 00400648 O' Ring 31 00604189 Diverter Assembly

9 00411240 Spline Adaptor 32 00650492 Thermostatic Cartridge

10 00410544 Handle Cap 33 00940006 Seating Ring

11 00411048 Temperature Over ride Button 34 00400262 O' Ring

12 00411057 Temperature Stop Ring 35 00400008 O' Ring

13 00411171 Plastic Spacer 36 00500219 Grub Screw

14 00411398 Flow Regulator 10 l/min LP 37 00141699 Stopcock Body

15 00500144 Grub Screw 38 00400030 O' Ring

16 00500222 Spring 39 00512115 Connector

17 00500492 Temperature Stop Pin 40 00400100 O' Ring

18 00500700 Grub Screw 41 00512619 Stopcock valve seat

19 00510133 Nut 42 00650307 Stopcock Valve

20 00511135 Nut 43 00515922 Adaptor

21 00511137 Olive 44 00501037 Spacer

22 00511258 Connector 45 00500746 Stopcock Spline Extended Screw

23 00512620 Connector

1 2 3 4

Comentários a estes Manuais

Sem comentários

Methven Kiri Manual do Utilizador Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Para a casa Methven Kiri